The AC Infinity CLOUDCOM 6 is the new controller that ships with the CLOUDLINE T-series fans and the Air Filtration Kit Pros. It can run a fan, a light, a humidifier or a sensor on its own, and it connects to your phone for the fine tuning. This guide walks through first power-up, the programming modes, what the little icons on the screen are telling you, and how to pair it with the app. Keep the CLOUDCOM 6 quick start guide (PDF) open next to you if you like a second opinion.

What the CLOUDCOM 6 can run

The controller has six ports, and each one runs a device or a sensor with its own programming. That means a fan on port 1 can follow temperature while a light on port 2 follows a clock. If six is not enough, compatible hubs add more wired ports, and Thread mesh lets you add compatible wireless devices (they need the Thread receiver) up to 100 in total.

CLOUDCOM 6 controller overview chart

A few specs worth knowing before you start:

  • Power levels: each device runs on 10 levels, from 1 to 10, plus off.
  • Built-in sensors: the controller reads temperature, humidity and VPD.
  • Connections: the app talks to the controller over Bluetooth or Wi-Fi (2.4 GHz and 5 GHz).
  • Programs: temperature, humidity and VPD triggers, timers, cycles and schedules, plus more advanced programs built in the app.
  • Display settings: Fahrenheit or Celsius, sensor calibration, screen lock, and a maximum and minimum level for each device.

Here is the controller itself, so you know which button is which for the rest of this guide.

CLOUDCOM 6 controller diagram showing the buttons, ports and display

Quick start: first power-up

1. Plug everything in before you power on

Connect the sensor probe and the power adapter to the controller, and connect your fan or other device, before you turn anything on.

CLOUDCOM 6 quick start step 1, connect the sensor, power and devices

2. Pick a device

Press the Port button, use the up and down buttons to reach the device you want to set up, then press Select to open that device's page.

CLOUDCOM 6 quick start step 2, select a device with the port button

3. Choose a mode

Pick one of the available modes for that device and adjust its settings. You can change your mind at any time.

CLOUDCOM 6 quick start step 3, choose a mode

If you bought the fan with the controller, the fan and the controller are connected with the UIS cable in the box, and the sensor probe should be placed at plant height rather than next to the fan. Keep the probe cable away from the power leads of any HID ballast so the readings stay clean.

The programming modes, in plain English

Manual

You set the level yourself, anywhere from off to 10. It holds that level until you change it. Good for a fan you just want running steady.

CLOUDCOM 6 Manual mode screen

Sensor

The device turns on and off based on a climate trigger, such as temperature rising above your target. This is the mode most people choose for an exhaust fan.

CLOUDCOM 6 Sensor mode screen

Timer to On

A one-time countdown. When it finishes, the device turns on.

CLOUDCOM 6 Timer to On mode screen

Timer to Off

The same idea in reverse: when the countdown finishes, the device turns off.

CLOUDCOM 6 Timer to Off mode screen

Cycle

You choose how long the device runs and how long it rests, and it repeats that pattern on a loop. A common use is a few minutes of fresh air every hour.

CLOUDCOM 6 Cycle mode screen

Schedule

You pick a daily on time and off time, and the device repeats that every day. This is the one to use for lights.

CLOUDCOM 6 Schedule mode screen

Two settings that make sensor mode behave

Transition

Instead of jumping straight from off to full speed, the device steps its level up the further the reading drifts from your target. A tent that is a degree warm gets a gentle breeze, and one that is ten degrees warm gets full power.

CLOUDCOM 6 Transition setting explained

Buffer

A buffer gives the device a separate on trigger and off trigger, so it does not click on and off every time the reading wobbles around the target. If your fan keeps starting and stopping, widen the buffer.

CLOUDCOM 6 Buffer setting explained

What the screen icons mean

Advanced programming

The controller is following a program you built in the app instead of a simple on-screen mode.

CLOUDCOM 6 advanced programming icon

Bluetooth or Wi-Fi

The controller is currently connected to the app.

CLOUDCOM 6 Bluetooth and Wi-Fi connection icon

Display lock

The screen is locked. Hold the Settings button to lock or unlock it.

CLOUDCOM 6 display lock icon

Device error

Flashes when a connected device reports a problem. Check that device and its connections.

CLOUDCOM 6 device error icon

Thread

A device with a Thread receiver has connected to the controller over Thread mesh.

CLOUDCOM 6 Thread connection icon

Connecting the controller to the app

Before you pair

Download the AC Infinity app by searching for AC Infinity in the Apple App Store or Google Play. Android phones will ask for location permission, because that is how the phone finds a nearby controller. Allow it for pairing.

Update the firmware

Check for a firmware update after pairing. Open your controller from the Devices screen, tap the gear icon in the top right, then choose Device and Firmware Update. The controller turns off briefly while it updates, so do it when your fan can take a short break.

AC Infinity app firmware update step 1

AC Infinity app firmware update step 2

AC Infinity app firmware update step 3

Pair it

Step 1

On the Devices screen, tap the plus button in the top right and choose your controller.

Pairing the CLOUDCOM 6 with the AC Infinity app, step 1

Step 2

On the controller, hold the Port button for 5 seconds to put it in pairing mode. If the app does not find it, continue with manual pairing.

Pairing the CLOUDCOM 6 with the AC Infinity app, step 2

Step 3

Choose whether to connect over Bluetooth or Wi-Fi.

Pairing the CLOUDCOM 6 with the AC Infinity app, step 3

Step 4

For Wi-Fi, you need an AC Infinity account and your Wi-Fi login. Make sure you are signed in before you continue.

Pairing the CLOUDCOM 6 with the AC Infinity app, step 4

Step 5

Tap Done. The controller now appears in your app with its own ID.

Pairing the CLOUDCOM 6 with the AC Infinity app, step 5

Bluetooth is enough for setting things up while you are standing next to the controller. Wi-Fi is what lets you check on the tent and get alerts when you are away.

Which Happy Hydro products ship with a CLOUDCOM 6

The T-series CLOUDLINE fans and the Air Filtration Kit Pros come with the controller. The Cloudline T6 is a good place to start for most 4x4 and 5x5 tents. The fan manuals are also on our site: the CLOUDLINE S and T series manual (PDF) and the Air Filtration Kit Pro manual (PDF).

Stuck on a step? Call us at 716-217-0353 or email help@happyhydro.com and we will walk through it with you.

Leave a comment

All comments are moderated before being published

Our Philosophy

Our bottom-line commitment is to have happy customers.

Rather than focusing on raising margins and obsessing over profits, we've achieved an extraordinary customer retention rate by offering competitive prices, superior products, and – perhaps most importantly – world-class customer service.

Our philosophy will never change: When you're happy, we're happy.